The Kamry 30 Watt Box Mod Vape is the perfect way to vape dry herbs, wax and oils all in one vaporizer. You can attach any 510 thread vape tank attachment to this box Mod.
Kamry Box Mod Vape Kit Includes
- 1x 30 Watt Box Mod (Kamry 30w V1)
- 1x micro USB vape charging cable
- 1x user manual
- 1x protective vape travel case
Kamry Box Mod Vape Details
- Box mod will shut down after 10 seconds of use to ensure safety
- Fit for 0.3ohm-9.9ohm atomizers
- OLED screen displays battery power, puff count, wattage, voltage, atomizer resistance
- Atomizer connection: spring pin, 510 thread
- Input Voltage - 3.1-4.2V
- Output Voltage - 1.4-8V
- Variable Wattage: 7W-30W
- Battery Capacity: 2100mah
- Height: 3 inches
- Length: 1.375 inches
- Width: 0.75 inches
Kamry Box Mod Vape FAQ
How to use the Kamry 30 Watt Box Mod Vape
- Press the power button 5 times consecutively to turn the box mod on/off
- Use the +/- buttons to set the Wattage. The higher the wattage the more powerful vape hit you can take. If you're using a 510 thread dry herb atomizer such as the Yocan 94F, make sure the wattage is set at 10 watts or less. Dry herb Vaporizer atomizers don't need a lot of wattage to light up. If you set the wattage too high, you'll burn out the coil and break it. The same goes for wax atomizers such as the Yocan Cerum Vape Tank for Wax. Most e-liquid tanks such as the Kamry Zealot Eliquid Atomizer, Q Tank, and the Kangertech Tank can all handle 30 watt box mod batteries.
When to change an e-liquid atomizer?
- The atomizer is the most important part to any vaporizer. It turns the e-liquid into vapor by heating a coil that is in contact with a piece of wick. Subsequently, it absorbs the e-liquid.
- It's inevitable that you will have to change your coil at some point. Think of it as a light bulb. A light bulb will last you a long time, but at some point it burns out and you need to change the bulb.
- The lifespan of an e-liquid atomizer depends on the user. The more frequently you vape, the more often you will need to change it. Two other factors that can affect the lifespan is if your e-liquid has too much sweetener in it or you're setting your box mod wattage at a very high temperature all the time.
- Below are some indicators of knowing if you need to change your Vape Coil
- The flavor of your e-liquid will have a burnt taste to it.
- You won't get as much vapor as you usually get.
- Overtime, sometimes your tank starts to leak. If that happens, you need to replace your tank immediately.
How to clean box mod and e-liquid vape tank?
- Cleaning your box mod is very easy. All you need is a Q-TIP and rubbing alcohol. Make sure to dip your Q-TIP in the rubbing alcohol and then clean out the 510 thread battery connection part. This is very important because if e-liquid continues to get inside the port, your vapor quality will gradually diminish.
- Cleaning your e-liquid tank is pretty simple too. When it's time to change out your atomizer, remove the coil from the tank, throw away the coil, and then wash the tank under water. Let the tank air dry and then screw in your new coil and begin vaping whenever you're ready.
Why does the device always go back automatically to the VW mode from TC mode?
- Please make sure that your resistance is correct, otherwise, the device will detect itself and will only be allowed to be set in VW mode. You can also try to screw off the eliquid atomizer and switch to TC mode in room temperature.
Why does the Box Mod sometimes show "device too hot" when pressing the power button?
- If you're continuously using the box mod to blow out huge clouds of vapor, you need to rest and let the battery cool down. The higher the wattage, the bigger the current. As a result, the temperature is higher and creates more heat. It's very important to be careful when using the box mod. You don't need to take 10 or even 20 consecutive vape hits. It's not a competition and you're not supposed to be using it like a toy. This is supposed to be an alternative to smoking, which means you take vape hits from time to time and don't need to vape the way some of you may chain smoke.
- You can also try to use TCR mode and set the TCR value according to the coil's material. If the value is not correct, the box mod will detect itself and give a wrong judgment and output.
Why does the LED start flashing while using?
- It means that you need to charge your box mod. Plug your micro USB cord into your box mod and use the other end to insert it into your computer or an A/C wall adapter. After a few hours, your box mod will be fully charged.